Home Basic Terminologies

Basic Terminologies

November 6th, 2011 in CCNA Wireless Knowledge Go to comments


An antenna is a device to transmit and/or receive electromagnetic waves. Electromagnetic waves are often referred to as radio waves. Most antennas are resonant devices, which operate efficiently over a relatively narrow frequency band. An antenna must be tuned (matched) to the same frequency band as the radio system to which it is connected otherwise reception and/or transmission will be impaired.

Types of antenna

There are 3 types of antennas used with mobile wireless, omnidirectional, dish and panel antennas.
+ Omnidirectional radiate equally in all directions
+ Dishes are very directional
+ Panels are not as directional as Dishes.


Decibels (dB) are the accepted method of describing a gain or loss relationship in a communication system. If a level is stated in decibels, then it is comparing a current signal level to a previous level or preset standard level. The beauty of dB is they may be added and subtracted. A decibel relationship (for power) is calculated using the following formula:


“A” might be the power applied to the connector on an antenna, the input terminal of an amplifier or one end of a transmission line. “B” might be the power arriving at the opposite end of the transmission line, the amplifier output or the peak power in the main lobe of radiated energy from an antenna. If “A” is larger than “B”, the result will be a positive number or gain. If “A” is smaller than “B”, the result will be a negative number or loss.

You will notice that the “B” is capitalized in dB. This is because it refers to the last name of Alexander Graham Bell.


+ dBi is a measure of the increase in signal (gain) by your antenna compared to the hypothetical isotropic antenna (which uniformly distributes energy in all directions) -> It is a ratio. The greater the dBi value, the higher the gain and the more acute the angle of coverage.

+ dBm is a measure of signal power. It is the the power ratio in decibel (dB) of the measured power referenced to one milliwatt (mW). The “m” stands for “milliwatt”.


At 1700 MHz, 1/4 of the power applied to one end of a coax cable arrives at the other end. What is the cable loss in dB?



=> Loss = 10 * (- 0.602) = – 6.02 dB

From the formula above we can calculate at 3 dB the power is reduced by half. Loss =  10 * log (1/2) = -3 dB; this is an important number to remember.


The angle, in degrees, between the two half-power points (-3 dB) of an antenna beam, where more than 90% of the energy is radiated.



OFDM was proposed in the late 1960s, and in 1970, US patent was issued. OFDM encodes a single transmission into
multiple sub-carriers. All the slow subchannel are then multiplexed into one fast combined channel.

The trouble with traditional FDM is that the guard bands waste bandwidth and thus reduce capacity. OFDM selects channels that overlap but do not interfere with each other.


OFDM works because the frequencies of the subcarriers are selected so that at each subcarrier frequency, all other subcarriers do not contribute to overall waveform.

In this example, three subcarriers are overlapped but do not interfere with each other. Notice that only the peaks of each subcarrier carry data. At the peak of each of the subcarriers, the other two subcarriers have zero amplitude.


Types of network in CCNA Wireless

+ A LAN (local area network) is a data communications network that typically connects personal computers within a very limited geographical (usually within a single building). LANs use a variety of wired and wireless technologies, standards and protocols. School computer labs and home networks are examples of LANs.

+ A PAN (personal area network) is a term used to refer to the interconnection of personal digital devices within a range of about 30 feet (10 meters) and without the use of wires or cables. For example, a PAN could be used to wirelessly transmit data from a notebook computer to a PDA or portable printer.

+ A MAN (metropolitan area network) is a public high-speed network capable of voice and data transmission within a range of about 50 miles (80 km). Examples of MANs that provide data transport services include local ISPs, cable television companies, and local telephone companies.

+ A WAN (wide area network) covers a large geographical area and typically consists of several smaller networks, which might use different computer platforms and network technologies. The Internet is the world’s largest WAN. Networks for nationwide banks and superstore chains can be classified as WANs.



Bluetooth wireless technology is a short-range communications technology intended to replace the cables connecting portable and/or fixed devices while maintaining high levels of security. Connections between Bluetooth devices allow these devices to communicate wirelessly through short-range, ad hoc networks. Bluetooth operates in the 2.4 GHz unlicensed ISM band.


Industrial, scientific and medical (ISM) band is a part of the radio spectrum that can be used by anybody without a license in most countries. In the U.S, the 902-928 MHz, 2.4 GHz and 5.7-5.8 GHz bands were initially used for machines that emitted radio frequencies, such as RF welders, industrial heaters and microwave ovens, but not for radio communications. In 1985, the FCC Rules opened up the ISM bands for wireless LANs and mobile communications. Nowadays, numerous applications use this band, including cordless phones, wireless garage door openers, wireless microphones, vehicle tracking, amateur radio…


Worldwide Interoperability for Microwave Access (WiMax) is defined by the WiMax forum and standardized by the IEEE 802.16 suite. The most current standard is 802.16e.

Operates in two separate frequency bands,  2-11 GHz and 10-66 GHz
At the higher frequencies, line of sight (LOS) is required – point-to-point links only
In the lower region, the signals propagate without the requirement for line of sight (NLOS) to customers

Basic Service Set (BSS)

A group of stations that share an access point are said to be part of one BSS.

Extended Service Set (ESS)

Some WLANs are large enough to require multiple access points. A group of access points connected to the same WLAN are known as an ESS. Within an ESS, a client can associate with any one of many access points that use the same Extended service set identifier (ESSID). That allows users to roam about an office without losing wireless connection.

IEEE 802.11 standard

A family of standards that defines the physical layers (PHY) and the Media Access Control (MAC) layer.

* IEEE 802.11a: 54 Mbps in the 5.7 GHz ISM band
* IEEE 802.11b: 11 Mbps in the 2.4 GHz ISM band
* IEEE 802.11g: 54 Mbps in the 2.4 GHz ISM band
* IEEE 802.11i: security. The IEEE initiated the 802.11i project to overcome the problem of WEP (which has many flaws and it could be exploited easily)
* IEEE 802.11e: QoS
* IEEE 802.11f: Inter Access Point Protocol (IAPP)

More information about 802.11i:

The new security standard, 802.11i, which was ratified in June 2004, fixes all WEP weaknesses. It is divided into three main categories:

1. Temporary Key Integrity Protocol (TKIP) is a short-term solution that fixes all WEP weaknesses. TKIP can be used with old 802.11 equipment (after a driver/firmware upgrade) and provides integrity and confidentiality.
2. Counter Mode with CBC-MAC Protocol (CCMP) [RFC2610] is a new protocol, designed from ground up. It uses AES as its cryptographic algorithm, and, since this is more CPU intensive than RC4 (used in WEP and TKIP), new 802.11 hardware may be required. Some drivers can implement CCMP in software. CCMP provides integrity and confidentiality.
3. 802.1X Port-Based Network Access Control: Either when using TKIP or CCMP, 802.1X is used for authentication.

Wireless Access Points

There are two categories of Wireless Access Points (WAPs):  
* Autonomous WAPs
* Lightweight WAPs (LWAPs)

Autonomous WAPs operate independently, and each contains its own configuration file and security policy. Autonomous WAPs suffer from scalability issues in enterprise environments, as a large number of independent WAPs can quickly become difficult to manage.

Lightweight WAPs (LWAPs) are centrally controlled using one or more Wireless LAN Controllers (WLCs), providing a more scalable solution than Autonomous WAPs.


Encryption is the process of changing data into a form that can be read only by the intended receiver. To decipher the message, the receiver of the encrypted data must have the proper decryption key (password).


TKIP stands for Temporal Key Integrity Protocol.  It is basically a patch for the weakness found in WEP.  The problem with the original WEP is that an attacker could recover your key after observing a relatively small amount of your traffic.  TKIP addresses that problem by automatically negotiating a new key every few minutes — effectively never giving an attacker enough data to break a key.  Both WEP and WPA-TKIP use the RC4 stream cipher.

TKIP Session Key

* Different for every pair
* Different for every station
* Generated for each session
* Derived from a “seed” called the passphrase


AES stands for Advanced Encryption Standard and is a totally separate cipher system.  It is a 128-bit, 192-bit, or 256-bit block cipher and is considered the gold standard of encryption systems today.  AES takes more computing power to run so small devices like Nintendo DS don’t have it, but is the most secure option you can pick for your wireless network.


Extensible Authentication Protocol (EAP) [RFC 3748] is just the transport protocol optimized for authentication, not the authentication method itself:

” EAP is an authentication framework which supports multiple authentication methods. EAP typically runs directly over data link layers such as Point-to-Point Protocol (PPP) or IEEE 802, without requiring IP. EAP provides its own support for duplicate elimination and retransmission, but is reliant on lower layer ordering guarantees. Fragmentation is not supported within EAP itself; however, individual EAP methods may support this.” — RFC 3748, page 3

Some of the most-used EAP authentication mechanism are listed below:

* EAP-MD5: MD5-Challenge requires username/password, and is equivalent to the PPP CHAP protocol [RFC1994]. This method does not provide dictionary attack resistance, mutual authentication, or key derivation, and has therefore little use in a wireless authentication enviroment.
* Lightweight EAP (LEAP): A username/password combination is sent to a Authentication Server (RADIUS) for authentication. Leap is a proprietary protocol developed by Cisco, and is not considered secure. Cisco is phasing out LEAP in favor of PEAP.
* EAP-TLS: Creates a TLS session within EAP, between the Supplicant and the Authentication Server. Both the server and the client(s) need a valid (x509) certificate, and therefore a PKI. This method provides authentication both ways.
* EAP-TTLS: Sets up a encrypted TLS-tunnel for safe transport of authentication data. Within the TLS tunnel, (any) other authentication methods may be used. Developed by Funk Software and Meetinghouse, and is currently an IETF draft.
*EAP-FAST: Provides a way to ensure the same level of security as EAP-TLS, but without the need to manage certificates on the client or server side. To achieve this, the same AAA server on which the authentication will occur generates the client credential, called the Protected Access Credential (PAC).
* Protected EAP (PEAP): Uses, as EAP-TTLS, an encrypted TLS-tunnel. Supplicant certificates for both EAP-TTLS and EAP-PEAP are optional, but server (AS) certificates are required. Developed by Microsoft, Cisco, and RSA Security, and is currently an IETF draft.
* EAP-MSCHAPv2: Requires username/password, and is basically an EAP encapsulation of MS-CHAP-v2 [RFC2759]. Usually used inside of a PEAP-encrypted tunnel. Developed by Microsoft, and is currently an IETF draft.


Remote Authentication Dial-In User Service (RADIUS) is defined in [RFC2865] (with friends), and was primarily used by ISPs who authenticated username and password before the user got authorized to use the ISP’s network.

802.1X does not specify what kind of back-end authentication server must be present, but RADIUS is the “de-facto” back-end authentication server used in 802.1X.


Roaming is the movement of a client from one AP to another while still transmitting. Roaming can be done across different mobility groups, but must remain inside the same mobility domain. There are 2 types of roaming:

A client roaming from AP1 to AP2. These two APs are in the same mobility group and mobility domain


Roaming in the same Mobility Group

A client roaming from AP1 to AP2. These two APs are in different mobility groups but in the same mobility domain


Roaming in different Mobility Groups (but still in the same Mobility Domain)

Note: If you want to learn more about Wireless, please read my Wireless tutorial

Comments (50) Comments
Comment pages
  1. VamBoo
    October 13th, 2017

    Who someone tell me that where is premdev URL?

  2. Virat Kolhi
    October 23rd, 2017

    Please, show me the way to get premdev materials

  3. Yash
    November 16th, 2017

    hi please send me latest CCNA Wireless dumps if any body have..
    would be great help.. i really need help..
    pls pls pls

    send me on . .. {email not allowed}

  4. Baba
    December 6th, 2017

    Please share with me the dumps for CCNA Wireless 200-355.
    Thanks in advnnce

    sibusisofrans @ gmail. com

  5. Logan
    December 9th, 2017

    I took the CCNA Wireless today and I passed it. I used the dumps from Pass Leader. Around 75% of the questions were the same. I saw like 10 new questions but nothing complicated. My suggestion is, read the book then use the dumps and analyze each questions, take notes and practice with the VCE player included in the package. They have 5 exam and a total of 500 questions.

  6. NewOne
    December 13th, 2017

    I read book and start Pass Leader Free dumps. There are many questions that are not covered in book. Can somebody who took exam writte some questions?Is there any better dumps?
    @Logan, how much differ free pass leader from premium?I see that premium has 500Q.

  7. Logan
    December 17th, 2017

    @NewOne, I used the premium dumps. With the free ones you only get a portion of the questions. You are right, some questions are not cover in the book. Like I said my recommendation is buy the premium package and use the VCE Player to practice. I took the exam a week ago a most of the questions are there and if you read the book you will be in the capacity to answer the new questions without any issue.

  8. ssay
    December 26th, 2017

    Please can some one send/shard me dumps for the wifund exam (200-355).
    I’ll take my exam 01/16/2018.
    my @ is *** univernet at free dot fr ***
    Thanks for all.

  9. markv
    December 27th, 2017

    Can someone please add the link to download the materia for exam 200-355, will be much apreciated @Logan congrats can u please sharee

  10. Anonymous
    December 27th, 2017

    Latest ccie 400-101 exam questions http://cciedump.spoto.net/ccna-security.php
    100% Passing Guarantee

  11. liben
    January 17th, 2018

    Updated Question Answers available on: https://dumpsgator.com/vendor/Cisco-braindumps-questions

  12. Sandeep Singh
    January 17th, 2018

    Cisco Wireless Solution : Local Mode Vs Flex Connect

  13. deej
    January 23rd, 2018

    HY guyz today i am share my Implementing Cisco Wireless Network Fundamentals Exam experience with you i will get excellent score in this exam by learning 200-355 dumps i get from pass4surekey. https://www.pass4surekey.com/exam/200-355.html Wish you all the best

  14. Monika
    January 25th, 2018

    From where can i get valid dumps for CCNA wireless?

  15. dumpspro
    January 26th, 2018
  16. nancy peter
    January 31st, 2018

    Thanks @saleena for suggesting me http://www.braindumpscerts.com/ for exam preparation, I just cleared my 200-355 exam on the first attempt!

  17. Anonymous
    February 19th, 2018

    wereis the login page??????

  18. dumpspro dot com
    March 2nd, 2018
  19. Ahmed
    May 13th, 2018

    Hi, any news about a valid dump, anybody passed recently

  20. 34534534fsdf
    May 21st, 2018

    latest CCNA Exam Questions


  21. .
    June 28th, 2018

    Felix your a fraud

  22. 0815
    July 24th, 2018

    Can somebody tell, if there are still many Cisco WCS questions in the exam ?
    It not supported any more and end of life…
    Cisco: “NOTE: This product is no longer being sold and might not be supported.”

  23. deltot
    August 13th, 2018

    Hi, Could anyone send me the latest dumps for CCNA WIRELESS 200-355? mautorre77 @ gmail. com

  24. xiuo
    August 14th, 2018

    http: / /t .cn/R DuDldn
    I passed the exam with a high score, only read the questions inside, share it with you, and wish you good luck.

  25. Anonymous
    August 19th, 2018

    Got 89% score in ccna 200-125 exam with guide of and learning material of https://www.realdumpspdf.com/exam/200-125-dumps-pdf/ Good Luck

  26. GRDT
    August 28th, 2018

    I purchased the CCIE exam materials. The information in this section is true and effective. Before the exam, the exam database will be updated to take the initiative to communicate with me. The attitude is very good. Any questions will be answered in time, and the information is comprehensive. No subjects have I passed the exam and shared it with you. I hope to help you too. h
    tt p:/ /t.cn/RDIfLIE

  27. Anonymous
    September 12th, 2018

    I recently used this exam and i am satisfied. My recommendation would be these 100% real exam questions 300-360 Dumps for Guaranteed Success. https://www.crack4sure.com/CCNP-Wireless-certification-training.html

  28. Anonymous
    September 20th, 2018

    Please share with me the dumps for CCNA Wireless 200-355.

    jeje pestel @ gmail dot com

  29. Anonymous
    October 16th, 2018

    Please share with me the dumps for CCNA Wireless 200-355.

    s_sitza@ hotmail dot com

  30. Bad Boys
    October 19th, 2018

    Hey Boys , somewere can share the latest dumps for CCNA Wireless 200-355,
    someone has taken the exam these days.

    Good Day

  31. Jan
    October 29th, 2018

    Could you please share the latest dump by email
    nag.fawzi at gmail dot com

  32. Anonymous
    November 4th, 2018

    Helloo , please anyone can send me CCNA-wirelees dump is valid ?
    My email : {email not allowed}

  33. Line 6
    November 21st, 2018

    CWNA… Does anyone have any study materials for the CWNA – 107 stuff or is this just a Cisco CCNA – Wireless site..

  34. egrg
    November 23rd, 2018

    Black Friday, the last day of the event, there is a need to hurry to see, missed today, we have to wait for next year, such a preferential event, the focus is that the test bank is up to date, has been updated, and is free to provide updates.
    H t t p :t.cn/E7mOgxN

  35. jkh
    January 17th, 2019


    Here is worth recommending.

  36. romail
    January 27th, 2019

    please some body can send me the new dump will be appreciated.
    romailside @ gmail

  37. Anonymous
    February 18th, 2019


    Just passing the exam, people in need can give it a try.

  38. agfdagdf
    March 14th, 2019

    Cisco (CCNA CCNP CCIE) exam study materials, Cisco study guide, materials are reliable, very stable

  39. gfgfdafd
    April 25th, 2019

    Real and effective CCIE 400-101 dump, the dump just updated is now very stable

  40. kiki
    May 23rd, 2019

    Share latest Update wireless exam question

  41. I’m a real person, but anonymous for now, I hope
    June 4th, 2019

    Why has this site become a dumping point for fake dumps that lead people on. There are honest hard working tech folks in there that just want to pass tests with legit dumps and test resources. I paid for the premium membership while going thru my ICND1 studies and it worked in my favor big time. Now I need to prep for my 200-355 and all we see is stupid links to nowhere or links to worthless sites that are only looking to steal a buck or two. Whats the point of having a site like wirelesstut.com if you cant trust a single post in here..

    That being said, who in here has legit dumps of questions to prepare for 200-355. Money doesnt grow on trees (well, the paper comes from trees, LOL) and spending it for worthless dumps is making this site a joke. Anyone, Bueller, Bueller…

    Seriously appreciate a real tech person with a link or question dump to help.

    Appreciate the help…

  42. I’m a real person, but anonymous for now, I hope
    June 4th, 2019

    I see many sharing what looks like legit questions in their posts, tell me you all have some kind of dumps that work.

  43. I’m a real person, but anonymous for now, I hope
    June 4th, 2019

    Also, I’ve asked this question before, but is there a premium login for wirelesstut.com like there was for 9tut.net

  44. pass(No spaces)hot dot com
    June 6th, 2019

    Hello, share latest exam questions Good luck, all!
    Look My Name

  45. nick
    June 20th, 2019

    Can someone please share legitimate dumps of CCNA wireless to sidebottem123 @ gmail

  46. xerg
    June 25th, 2019

    Someone can share the correct dumps for exams ccnp wireless?

  47. Dem
    October 2nd, 2019

    Please how to get the questions and answers?

    With CCNA R&S and CCNP, we put only renegate on the search field and obtain the pdf format of questions but I don’t see the file for ccna security

  48. abdulrahman
    January 14th, 2020

    can anybody send CCNA Wireless 200-355 dump

  49. abdulrahman
    January 14th, 2020

    can anybody send CCNA Wireless 200-355 dump to my email {email not allowed}

Comment pages

Reload Image